Project 𝑛+1 ≆ heat

The wood-burning stove is, itself, fine, but its installation appears to have been cobbled together by a drunken installer then bashed into the house — no doubt without those annoying or inconvenient permits or building codes. We have it sorted, for now.

But, next on the task list is getting the 50 year old electric furnace sorted out. We’re entering fall and overnight outdoor temps are dropping to about -5℃. When we enter the depths of winter, we’ll see daytime temps as low as -25℃. Sure, a fireplace is “cozy”, but we won’t want to rely solely on the fireplace all winter.

I’d like to get the ancient electric furnace working. I don’t want the indoors to be a tropical 28℃ in the winter. But I’d be happy if we could have a safety-limit of 15℃.

A couple of things can be readily determined — well, apart from its extraordinarily-obvious “It doesn’t work” condition.

It hasn’t a thermostat. Not a big deal, one can just jumper the two wires on a simplistic furnace. And, while this particular, er, domicile absolutely cannot justify a smart-thermostat, just any thermostat will work. I think I’ve still the old Honeywell thermostat that I’d replaced in the Moses Lake house with a Nest. That’ll solve the thermostat problem.

Are its breakers tripped? Nope — they’re fine. At the service panel and the on-appliance breakers.

There’s not a chance in hell that anything in here would be quick to repair. Dig in and make a list of every potential at plausible fault points:

Visual appearance of the exterior:

The low-voltage thermostat wiring (24VAC) needs a jumper wire between two terminals. On an older style HVAC, wires for the thermostat were typically connected to terminals L and 2. Terminal 2 would then be shunted to terminal C.

Shown here: quickly extended term 2 to C

Just looking at it, one could see that the jumper wire was simply folded back out of the way. Why in the world would they have disconnected that? Were they gnawing on the wires to strip off a few inches of insulation then attaching them and hoping for the best? Eh, easy enough to correct. But that’s not all, with certainty.

Is it in “winter” mode? Yep. That’s a switch to turn off, or switch between enabling heat or blower only.

Knowing that previous occupant fancied himself an electrician, I’ll have to look at the innards of wiring… he no doubt “fixed” it thinking he was going to make it work or work better (or work more better?). Ah, yep… he fixed it so well that the power wires for the blower itself have been cut…

…then spliced together… others disconnected and ends removed entirely.

Quite fortuitously, manufacturers back in the day, Coleman in this case, included a complete wiring diagram inside the service panel.

That’s a win right there.

There’s but one of me to do the work, and I’ve a limited amount of time available during the week to work on prioritized corrections to make this, uh, habitation livable. Sure, there are other extremely important issues to be sorted as well, but during the time I have available, I need to address one problem at a time.

  1. Identify everything non-standard.
  2. Remove all of the fixes.
  3. Restore it to its original condition.

So, it doesn’t work yet.

But it will.

Sometimes the Project Picks You

I had quickly pulled all of the receptacles to tackle later, but stumbled into this little gem just before I left for the week.

<sarcasm> Gosh, I have no idea why electrical at this end of the house is wonky. </sarcasm>

Count the number electrical issues this single modern receptacle:

  • That corroded (1) wire is meant to be the ground wire for the 14/2 cable.
  • It’s connected to the push-in neutral (2) side of the receptacle.
  • It’s aluminum, into a modern copper-receptacle (3).
  • There’s a neutral wire not connected (4).
  • There’s a hot (black) wire that’s connected to the grounding bus (5) for the receptacle.

At least the wires that I can see are routed the correct way round the terminals.

I think I have my Friday project selected.

Pondering, Still

Here we are in the midst of something of an unknown for the future of society, and yet I find that I’m pondering, again, buying another bicycle.

My list has evolved a bit from what it was. Previously, I had considered:

  • Salsa Journeyman Apex
  • Aventon Pace 500
  • Rad Runner

I’ve disregarded two of them because one was somewhat impractical for my current locale and lifestyle. I’d end up adding racks and baskets front and rear and likely go as far as to attach a pair of my ammo cans. Yes, it would look cool — but it’s just not going to be meaningful for me presently.

Another wasn’t quite what I’d prefer. Sure, I could swap out the Café bars for flat or drops, but the cost would become somewhat limiting. Off they’d go.

A straightforward and seemingly obvious answer: Salsa Journeyman Apex — to which I’d upgrade to tubeless, add pedals of choice and Bob’s your uncle.


But I find that I rather like the idea of an eBike.


Because I’m not going to live forever. And having a bit of extra power for the lengthy uphill climbs seems like it could be quite helpful.

A gravel bike, yes. I mean, I already have a touring-class bike. Quite heavy for casual riding and rather purpose-made for carrying substantial loads long distances.

Right, so I removed two, then added two alternates. Both additions are eBikes. Of course, one holdover from the previous list. So, now it’s changed to:

*Why the holdover? Alternative question: won’t an eBike just make you lazy?

For my needs, a 650B is more agreeable — not “balloon” tires, so to speak, but certainly more comfortable.